When constructing a well, we imagine how we will drink tasty, crystal and well-chilled well water directly from a galvanized bucket. But the reality is sometimes far from fantasy, and we find that the state of the water does not inspire confidence. The result of quenching thirst can be unpredictable and even dangerous. Do you agree?
We will explain why muddy water in the well will explain in detail how to eliminate the causes of this phenomenon. The article presented for consideration describes all kinds of reasons that affect the purity and chemical composition of water in a private source. Here you will learn not only about the methods of cleaning and disinfection, but also about the rules of prevention.
Causes of turbidity in the well
As a rule, well owners prefer to drink water from a natural source, even if they are connected to a central water supply.
It is believed that water produced independently is akin to spring water and is healthier than that which undergoes chlorination. But over time, the water we received from the well loses its transparency. What can cause such an unpleasant phenomenon?
Based on the assertion that we are exactly what we eat and drink, we should not drink contaminated water in any case
Well tightness
When constructing a well, reinforced concrete rings, which are integral parts of this structure, are installed on top of each other. The seams between them are sealed.
But, over time, the movement of the soil can lead to a partial displacement of the rings relative to each other. In this case, the tightness of the seams is also violated.
The seams between the rings of the well shaft are best reinforced with special brackets, this will become a prevention against seasonal displacement of them relative to each other
Spring floods, heavy rains and widespread snowmelt create an excessive load on the joints of the rings, as a result of which contaminated water begins to flow into the well. A haze forms.
I don’t want to not only drink such water, but also use it for everyday household needs. Moreover, in clouded water, hazardous chemicals may be present in dissolved form.
Image Gallery
Photo from
Decreased water quality in old wells
Yellow muddy water due to fungus
When deepening a water intake in a ferruginous soil
High water pollution
Mine well needs to be equipped
There is no quality water without a bottom filter
Incorrectly selected bottom filter
Bottom filter replacement required
Changes in the composition of the aquifer
Sometimes dirt does not penetrate the well through the seams between the rings. They can poison the aquifer itself, due to which the structure is filled with water. This happens if there is an enterprise located near your site that merges its industrial effluents into a natural reservoir, destroying it and the territory adjacent to it.
In this case, the water can not only become cloudy, but also acquire an unnatural color. The shade of the liquid will depend on what type of contamination affected it. The pollution of this type is the most difficult to fight: treatment of well water will not bring the desired result.
Indeed, new portions of water from the supply layer will return the problem. One can only hope for a filter system that should be placed in the path of water from the source to the place of its final consumption.
Causes of excess iron
If yellow water has appeared in your well, then this can be caused by industrial effluents and high iron content.In the first case, the color of the liquid is, as a rule, strongly pronounced and may be accompanied by a chemical odor. In the second - only a shade of water will be yellowish.
A yellowish tint always gives out water, the iron content in which exceeds the norm. A special filter system helps to cope with this situation.
To eliminate the high iron content, it is necessary to use special filters that can provide such cleaning.
Water stagnation problem
Another reason for clouding of water in a well can be stagnation. Perhaps the water source is not used as often as we would like. Water does not renew and stagnates.
Organic matter entering the well shaft from the outside begins to decompose. This process is accompanied by an unpleasant odor of hydrogen sulfide and a change in the color of the liquid.
Of course, you can’t drink such water, and you don’t want to: it has a specific aftertaste. Smell, color and taste arise due to the development of putrefactive bacteria in the water. This problem is corrected by the method of cleaning the well. It’s just that you will have to clean and disinfect the water source more than once, but regularly, without forgetting to devote proper attention and time to this process.
Well design defects
When direct sunlight freely penetrates the mine, ultraviolet light creates ideal conditions for the development of bacteria and the multiplication of microorganisms. The fact that the “process has begun” will be signaled to us by a greenish tint of water and an unpleasant odor. In especially advanced cases, the walls of the structure can be covered with green mosses.
The well must be protected as much as possible from all kinds of debris and even direct sunlight falling into its shaft
Error installing pump
Sometimes the appearance of water in the well is not a concern, and its clouding occurs only after the pump is started. It turns out that the equipment is simply improperly installed and during operation raises sludge from the bottom, which causes turbidity of the water. This happens if the vibration pump is installed too close to the bottom or is very active and powerful.
If the operation of the pump became the cause of the change in the state of the liquid, it will have to be dismantled and reinstalled, having previously studied in detail the instructions for use of the equipment.
The distance from the suction part of the pump to the bottom surface should be no less than 70-80 cm. If the measures taken do not help, you should use a pump with a different type of liquid suction.
Methods for eliminating turbidity of water
If a problem arises, measures must be taken to resolve it. You will not drink and use muddy water with an unpleasant odor and taste for cooking? What can be done?
Well cleanup
The measures taken always depend on the source of the problem. If the turbidity is formed as a result of water pollution by pieces of silt and sand, it is necessary to install filters for mechanical cleaning, which will catch this suspension and prevent its removal from the water.
In order to qualitatively perform the entire rather large complex of works, you will need special devices and designs that facilitate this work
If the dirt brings with it water that seeps into the gaps between the rings of the mine, measures must be taken to eliminate the inlet openings for it. If the haze appears after heavy rains, then the reason for the pollution really lies in the lack of tightness of the seams.
When the cause of the trouble is established, you can begin to restore water quality.
To do this, you need:
- with a pump to pump out all the water in the well from the well shaft;
- armed with a scraper and a stiff brush, descend on the cable into the shaft in order to thoroughly clean the inner surface of its rings from deposits of any kind;
- disinfect the entire concrete surface of the shaft;
- scoop out all sludge, deposits and debris that accumulated there during operation from the bottom of the structure with buckets;
- examine the walls of the well: the joints of the rings, as well as cracks and chips found during the work, thoroughly lubricate with sealant;
- create a clay castle, if it was not foreseen during the construction of the well.
As a preventive measure to prevent water pollution, you can use a bottom filter from aspen.
What is a clay castle
Turbid water in the well shaft may appear both during its operation and almost immediately after digging. This happens if during the installation of the well a clay castle was not built - a structure that is intended as an artificial barrier for rain and melt water to get into the well.
In the construction of this well, a clay castle was originally provided, which many times reduced the risk of clouding of water and the need for subsequent work
Perhaps the castle was made, but over time it failed or did not meet the technological requirements. In this case, the old clay protection will have to be dismantled and a new, high-quality one installed.
The manufacture of a new clay castle is carried out in the following order:
- Material preparation. Take the oily clay and add sand to it so that it makes up at least 15% of the mixture. When 20% lime is added to the working mixture, its composition will improve. Make sure that the clay does not dry out during operation.
- Digging a trench. Around the upper ring of the well, dig a trench approximately 2 meters deep and 50 cm wide.
- Castle formation. The resulting trench must be hammered with clay and well tamped. Do not forget to make a slight deviation from the ring to the periphery, which will not allow rain and melt water to accumulate around the mine site. Crushed stone is poured onto the clay and the castle is concreted, making it as protected as possible.
Such a clay castle will perfectly protect the contents of the well, diverting water from the exterior walls of the structure.
We make disinfection of a well
The appearance of bacteria in well water is accompanied by the appearance of an unpleasant odor. That is exactly how hydrogen sulfide smells, which occurs in the process of their life. Such water should not be drunk. It is necessary to disinfect the well and get rid of bacteria.
There are two main ways to solve the problem:
- surface treatment with ultraviolet lamps;
- cleaning the mine with chlorine.
Which disinfection method is more effective? Let's figure it out.
UV treatment
The disadvantage of ultraviolet disinfection is the high cost of this procedure. The method has indisputable advantages: its application does not require significant preparatory work, and the taste of water treated with ultraviolet does not change after this procedure.
It turns out that ultraviolet will not have any relation to the well itself, since the place of the radiation source is the consumer’s house. This treatment is used as a preventive measure that can prevent the appearance of bacteria.
It turns out that cleaning with active chlorine is a non-alternative way to disinfect the mine. It is produced if it is believed that bacteria already exist in the water. After applying chlorine, you can also connect an ultraviolet installation.
Active chlorine stepwise purification
Unlike ultraviolet light, active chlorine can adversely affect human health. When applying it, it is necessary to carefully observe the recommended dosage.
Disinfection work is carried out by specialists equipped with protective equipment: respirators and special gloves. The procedure itself is strictly regulated by SanPiN.
Purification using active chlorine and bleach carries a risk to human health, therefore it is necessary to carefully study the recommendations for the use of these substances and strictly follow them
It is conditionally possible to divide the entire disinfection procedure into the following stages:
- preliminary work;
- well shaft cleaning;
- final disinfection.
At the stage of preliminary disinfection, it is very important for us to calculate as accurately as possible exactly what volume of water is currently in the well. Knowing the parameters of the rings forming the walls of the structure, and the water level in it, it is not at all difficult to calculate the volume.
Now we need to calculate the total weight of active chlorine, which we will fill in the mine, based on the fact that for every liter of water we need 10 grams. powder.
We fill in the substance and agitate the resulting solution. To do this, scoop up a liquid with a bucket and immediately pour it back. We repeat this maneuver several times, after which we close the shaft with a lid, allowing chlorine to do its work for the next 2 hours.
After two hours, you can start cleaning the mine. To do this, completely free it from water. Now the mine needs to be thoroughly cleaned by removing moss and slime from the walls, and from the day - silty layers and all kinds of garbage. All dirt must be lifted to the surface and disposed of by digging away from the well.
Detected defects in the seams and the rings themselves must be repaired. As a rule, a sealing mixture is used for these purposes.
We evaluate the condition of the walls: reveals cracks and leaky seams. Identified defects are eliminated by performing local repair work. Now the inner surface of the shaft should be disinfected. We prepare a solution at the rate of 3 gr. active chlorine or 15 gr. bleach per 1 liter of water and apply it to the surface using a hydraulic console, roller or brush.
After completing these works, you can close the well and wait until the column is completely filled with water.
The third, final stage of processing is re-disinfection. We will again need a chlorine solution. To prepare it, you need to dissolve 200 g in 1 liter of water. bleach.
The solution must be left to infuse for an hour. We divide the resulting composition: we do not need the upper part to the sediment, and pour the lower part into the well.
Well cleaning and disinfection is hard physical work, so you need to calculate your strength and capabilities well. It might be wiser to hire specialists
We mix the water in the well with a bucket, as we already did before, and leave it for a day. After a day, you need to do the same procedure again. Another day has passed, now you need to completely pump out all the water and wipe the walls of the shaft with brushes, a mop or any other similar device. Then the walls are rinsed with clean water.
Now we have to fill the column several times with water and completely pump it out. This process will be completed only when the water ceases to smell like bleach, and in it there will be no extraneous taste. We will show reasonable caution: over the next two weeks we will drink only boiled water.
Water quality is not always determined by taste and smell. It is better to confirm its characteristics with laboratory analysis. How to take a sample and where to pass it for research is described in detail in our article.
And here is the goal of our work and its final result. It should be remembered that our health and quality of life depend on the quality of water consumed.
This video presents different types of work aimed at a single result - to make the water that we get from the well tasty and safe for our health. Of course, the video is openly advertising in nature, but the overall workflow is presented in it clearly, accessible and in sufficient detail.
Clouding of water in a well is a signal that appears if the prevention of pollution in your well has failed. There are many reasons for this, and we described them in detail in this article, so that you can easily find the source of your own troubles.
Most of the troubles could have been avoided if we carefully read the instructions for the pump, provided for a cover and a canopy that protect the shaft from the sun and dirt, initially correctly position the well on a hill, do not forget about the clay apron along its perimeter, and so on.
Nevertheless, the situation is not fatal, and you can still fix it by following our advice or by contacting professionals who will certainly help you.
Want to share your own methods and subtle tricks to restore the quality of well water? Please write comments in the block below. Here you can ask a question and post unique photos with the cleaning process.