Due to improper operation, temperature changes and pressure spikes in the operation of autonomous heating systems, malfunctions can occur. The negative consequences in such situations are critical: starting with the breakdown of individual components, ending with the destruction of buildings and a serious threat to life.
To eliminate dangerous risks, a safety valve in the heating system will help. What is he like and what is his principle of action? We will consider these issues in our article. We will also analyze the varieties of such valves and indicate the main differences between them, consider the rules for installing in the heating system and give recommendations on the selection and configuration of safety valves.
What is a safety valve for?
Heating systems are filled with water, the temperature of which is approximately 15 degrees. Circulating in a closed circuit, the heat carrier heats up, significantly increasing in volume. At this time, the pressure exerted on the inner surface of the pipes and the devices installed in the system increases significantly.
Exceeding the permissible norm, in most cases more than 3.5 bar, results in:
- leakage in the joints of the pipeline parts;
- damage or rupture of connecting elements and pipes made of polymers;
- explosion of the boiler tank;
- short circuit of electrical equipment in the boiler room.
Solid-fuel boilers, in which it is difficult to regulate the heat transfer power, are the highest risk of emergency situations.
The performance of electric and gas equipment is quickly adjusted from starting to maximum performance and vice versa. Often there is a safety automatics in them, which shuts down the working elements when the temperature rises excessively.
The intensity of burning wood, coal and other types of fuel in a solid fuel boiler is adjusted by opening / closing the shutter. In this case, the heat transfer force does not change immediately, but gradually. Due to the inertia of the heat generator, the liquid coolant can overheat.
Together with a pressure-calculating pressure gauge and venting air from the system, the safety valve is often included in the safety group
When the firewood in the chamber warms up well, bringing the water in the network to the required temperature levels, the air is blocked and the active flame begins to die out.
However, in a hot state, the furnace continues to generate accumulated heat. Reaching 90-95 degrees, the coolant boils and starts the inevitable intense vaporization. As a result, a sharp jump in pressure is provoked.
It is in these circumstances that a safety valve is activated. When the boundary pressure parameter is reached, it opens the shutter, freeing the way out for the formed vapor. After stabilization of the values, the valve closes automatically and switches back to sleep mode.
Its installation is required not only for solid fuel, but also for steam boilers, as well as furnaces equipped with a water circuit. Many modifications of heating equipment are completed with these devices at the production stage. Often this valve is one of the elements of the safety group. Typically, the device is inserted directly into the heat exchanger or installed in a pipeline near the boiler.
Varieties of devices and principle of operation
The design of the drain valve includes two mandatory components: a locking part, consisting of a seat and a shutter, and a force-setting adjuster. There are several types of equipment that have their own characteristics. They are classified according to certain criteria.
Classification # 1 - by the clamp mechanism
In heating systems of private houses, apartments and industrial installations of low power, the spring type of the product is preferred.
The main working element of the device is the spring. She props up the membrane that overlaps the saddle. A washer is placed on the stem connected to the handle, into which the upper part of the spring abuts. The position of the washer and the pressure effect on the membrane are adjusted by the handle
The device has a simple and reliable structure, compact dimensions, the ability to combine with other elements of the safety unit, at an affordable price. The compression force of the spring mechanism depends on the pressure parameter at which the valve is activated. The adjustment range is affected by the springiness of the spring itself.
The principle of operation of spring fuses is as follows:
- the flow of water affects the shutter of the device;
- coolant movement is limited by spring force;
- critical pressure exceeds the compression force, lifting the spool rod up;
- fluid is sent to the outlet;
- the internal volume of water is stabilized;
- the spring closes the shutter, returning it to its original position.
The case of the springy device is made of high-quality high-strength brass using technologies and methods of hot stamping. Steel is used in the production of the spring. The membrane, seals and handle are made of polymers.
Some brands produce equipment with factory settings already set. Also in the range there are models that are customizable at the installation site during commissioning.
Valves are open and closed. In the first embodiment, the coolant is discharged into the atmosphere, in the second - it is discharged into the return pipe
Lever-load fuses are not so widespread. In private autonomous systems with a boiler, they are rarely mounted. Operation is concentrated in the industrial sector in large industries, where the diameter of the pipelines is at least 200 mm.
The force on the rod in such mechanisms is not given by a spring, but by a load hung on a lever. It moves along the length of the lever, adjusting the force with which the rod will be pressed against the saddle.
The lever-cargo valve opens when the pressure of the medium from the lower part of the spool exceeds the indicators emanating from the lever. After that, the water leaves through a special outlet.
Adjustment of the lever-cargo fuses is carried out by moving the rod along the lever. In order to prevent its unauthorized or accidental changes, the cargo is bolted, covered with a special casing and locked with a lock
The response pressure, as well as the setting range, is determined by the length of the lever and the mass of the load. Lever fuses are not inferior to spring devices in terms of reliability, but they are more expensive. Devices are installed on flanged pipe fittings with a nominal diameter of 50 or more.
Classification # 2 - by shutter lift
In low-lift safety valves, the shutter rises no higher than 0.05 in the diameter of the seat. The opening mechanism in such equipment is proportional.
It is characterized by low bandwidth and the most primitive design. Low lifting equipment is used on vessels with a liquid medium.
Full-height devices are equipped with a two-position opening mechanism. They equip not only vessels with liquids, but also systems in which compressible media circulate (compressed air, steam, gas)
Full-height appliances have a higher shutter speed. This means that their throughput is much better than the previous version, so they are able to dump larger volumes of excess coolant.
Classification # 3 - by speed
The valve cover of the proportional safety valves opens gradually. Typically, the magnitude of the opening is proportional to the increase in pressure exerted on the inner surface. Simultaneously with the rise of the mechanism, the volumes of discharged coolant gradually increase.
The design of the devices does not limit the possibility of their use in a compressible medium, but nevertheless they prevail in systems with water and other liquids.
Among the advantages of safety valves with proportional actuation speed are low price, simplicity of design, lack of self-oscillations, portioned opening at the level of values necessary to maintain specific operating parameters
The peculiarity of the on-off valves is the instantaneous operation with full opening after reaching the boundary marks of pressure in the system, at which the fuse lock opens.
Experts recommend operating these devices in compressible environments. Among their main disadvantages include the presence of characteristic self-oscillations of the shutter.
When installing a two-position valve in a heating system with a liquid coolant, it should be borne in mind that during a sharp opening of the shutter a large amount of water will be discharged.
Because of this, the pressure drops too quickly. The valve closes instantly, resulting in a water hammer. Proportional devices do not cause such risks.
Features of three-way emergency valves
We should also talk about a device not so well-known to consumers - a three-way valve with a manual or electric switch. It is used in heating systems with low temperature circuits.
The design of the fuses is equipped with three holes, one of which is input, two - output. The flow of the medium is controlled by a damper made in the form of a ball or rod. Moving fluid is redistributed by rotations.
Three-way fuses are suitable for condensing boilers and in cases where several different systems operate from the same heating equipment
Imagine the situation: the house has a heating circuit with a system of conventional radiators and a warm floor. Technical requirements for the functioning of the second option provide for not too high coolant temperatures.
The boiler heats the water at the same temperature for all systems. In such conditions, there is a need for a redistributing device, the tasks of which the three-way valve perfectly copes with.
He is responsible for the following functions:
- delimitation of areas;
- distribution of flux density by zones;
- facilitating mixing of the heat carrier from the main supply / return branches for sending colder water to the warm floor pipeline than to radiators.
In order not to exercise constant control over the temperature of the medium on your own, it is necessary to pay attention to the valve models equipped with a servo drive.
This device is powered by a sensor installed in a low temperature circuit. When temperature marks change, a locking mechanism is triggered, which opens or closes the fluid supply from the return line.
In more detail about the varieties of the three-way valve for heating and the criteria for its selection, we spoke in the next article.
Tips for choosing the best model
Before settling on a specific safety equipment, it is necessary to familiarize yourself in detail with the technical characteristics of the boiler installation.
At the operation of the safety valve, negative temperatures are negatively reflected. Therefore, a sufficiently important characteristic for the device is the presence of frost protection
Do not neglect the study of the manufacturer's instructions, which indicate all the limit values.
A decisive role in choosing a device for heating have several criteria:
- Boiler performance.
- The maximum allowable pressure of the medium for the heat output of the heating equipment.
- Diameter of the safety valve.
It should be checked that the pressure regulator in the device has a range within which the parameters of this or that boiler enter. Response pressure should be 25-30% more than the operating indicator required for stable operation of the system.
The higher the operating pressure, the less time the device must spend on tripping. The gap between the pressure at the start of movement and when the shutter is fully open should be 15% for a nominal value of less than 2.5 atm, 10% for higher parameters
The diameter of the safety valve cannot be less than the connector of the inlet pipe. Otherwise, constant hydraulic resistance will not allow the fuse to fully perform immediate tasks.
The optimal material for manufacturing equipment is brass. It has a low coefficient of thermal expansion, which eliminates the destruction of the body from the effects of strong pressure.
The control unit is made of heat-resistant plastic materials that retain the desired rigidity even when in contact with boiling liquid.
Installation and setup rules
Having planned the independent installation of a safety valve for heating, you should prepare a set of tools in advance. The work can not do without adjustable wrenches and wrenches, a Phillips screwdriver, pliers, tape measure, silicone sealant.
Before you begin, you need to determine the right place for installation. The safety valve is recommended to be mounted on the supply pipe not far from the outlet pipe of the boiler. The optimal distance between the elements is 200-300 mm.
All compact household fuses are threaded. To achieve complete tightness during winding, it is necessary to seal the pipe with tow or silicone. FUM tape is undesirable to use, since it does not always withstand critical heat
In the regulatory documentation that comes with each device, the installation process is usually scheduled step by step.
Some key installation rules are unchanged for all types of valves:
- if the fuse is not mounted as part of a safety group, a manometer is placed next to it;
- in spring valves, the axis of the spring should have a strictly vertical position and be located under the body of the device;
- in the lever-cargo equipment, the lever is placed horizontally;
- on the pipeline section between the heating equipment and the fuse, it is not allowed to install check valves, taps, valves, circulation pump;
- to prevent damage to the housing during rotation of the valve, you need to be selected with a key on the side where the screwing is carried out;
- a drain pipe that removes the coolant to the sewer network or return pipe is connected to the outlet of the valve;
- the outlet pipe is not led directly to the sewer, but with the inclusion of a funnel or pit;
- in systems where the fluid circulates in a natural way, the safety valve is set at the highest point.
The nominal diameter of the device is selected based on the methods developed and approved by Gostekhnadzor. In resolving this issue, it is more reasonable to seek the help of professionals.
If this is not possible, you can try using specialized online programs for calculation.
To reduce hydraulic losses during medium pressure on the valve plate, the installation of emergency equipment is performed with a bias to the boiler installation
Valve adjustment is influenced by the type of clamp structure.In the spring fixtures there is a cap. Pre-compression of the spring is adjusted by rotating it. The accuracy of these products is high: +/- 0.2 atm.
In linkage devices, adjustments are made by increasing mass or moving the load.
After 7-8 operations in the installed emergency device, the spring and the plate wear out, as a result of which the tightness can be broken. In this case, it is advisable to replace the valve with a new one.
How the safety valve is made and what it consists of:
Safety valve as part of a safety group:
More on choosing and installing the optimum safety valve:
The safety valve is a simple and reliable equipment that will protect the housing from unforeseen emergency situations that occur in heating systems. To do this, just select a high-quality device with suitable parameters, and then perform its competent setup and installation.
Choosing the right safety valve for your heating system? Maybe you still have questions, the answers to which you did not find in the above material? Ask them to our experts by leaving a comment under the article.
Or maybe you want to supplement the material with interesting facts and useful recommendations? Or share the experience of installing the valve yourself in the system? Write your opinion about the need for such a protective device, share tips for choice, based on personal experience.